DA40 Fuel Pump Operation

Post a reply


This question is a means of preventing automated form submissions by spambots.
Smilies
:) :D :lol: :( 8) ;) :scream: :scratch: :tap: :P :shock: :thumbsup: :thumbsd: :oops: 8) 8-) :x :cry: :roll: :!: :?: :idea: :arrow: :mrgreen: :bow :^ :< :-
View more smilies

BBCode is ON
[img] is ON
[url] is ON
Smilies are ON

Topic review
   

Expand view Topic review: DA40 Fuel Pump Operation

Re: DA40 Fuel Pump Operation

by Rick » Sat Sep 29, 2018 6:12 pm

Sandy wrote:I turn my fuel pump on:
Prior to start (hot or cold) to prime for about 3-5 seconds, then I turn it off to start the engine;
Prior to takeoff until 500’ AGL;
For about 30 seconds when switching tanks; and
Prior to landing, turning it off and raising the flaps when on the runway.

All other times the fuel pump is off.

Sandy
The same for me, except I do not use the fuel pump at all for hot starts, and I have never turned it on to switch tanks.

Re: DA40 Fuel Pump Operation

by Sandy » Sat Sep 29, 2018 2:44 am

I turn my fuel pump on:
Prior to start (hot or cold) to prime for about 3-5 seconds, then I turn it off to start the engine;
Prior to takeoff until 500’ AGL;
For about 30 seconds when switching tanks; and
Prior to landing, turning it off and raising the flaps when on the runway.

All other times the fuel pump is off.

Sandy

Re: DA40 Fuel Pump Operation

by TJS » Fri Sep 28, 2018 1:16 am

:lol: mine quit at 710hrs, at Oshkosh this year on final. Talk about timing.

Re: DA40 Fuel Pump Operation

by Tom Davis » Sat Jul 14, 2018 10:13 pm

ThomasD wrote:I agree with Gordsh and others - I do the same. (Plus pump on at final approach as well.)

FYI one thing that I do not do [which is recommended in the POH] is to switch on the fuel pump when changing tanks in flight, if I am 3,000' or above.
I have never had a hiccup of the engine when just switching in-flight left-right or vice-versa without the pump on, so I don't do so (as the pump appears to have a quite limited life).

Formerly I did not turn on the fuel pump when changing tanks, but about 18 months ago I was flying out of KAVL (Asheville, NC) and switched tanks at about 9,000 feet above sea level (about 4,000 above ground level) and got an alert about low fuel pressure. Since then I have switched on the fuel pump when changing tanks. For what is worth, my 2005 vintage DA 40 is in the shop for what I believe will be a new fuel pump. The old pump has about 1200 hours on it.

Re: DA40 Fuel Pump Operation/check after maintenance

by ThomasD » Fri Mar 16, 2018 11:16 am

Free and correct? EVERY TIME.
I very much agree with this one. One time when I collected the airplane after maintenance, the control column was a bit 'sticky' in one direction. Turns out that the maintenance company had undone the earth bonding strap on the right aileron and whomever had put it back had left it rotated so that it snagged on the small fairing - something that I now always check pre-flight, that these earth bonding strips won't snag.
And pretty poor of the maintenance company not to do a 'full and free' check before releasing it back to me.

Another one I caught after maintenance (different company): the left wing was taken off to replace the inboard fuel sensor - so a careful inspection of the left wing, top and bottom of course? Yes, but I also found that the outboard inspection cover on the underside of the RIGHT wing was dangling loose - seems that the maintenance company undid both left and right wing inspection covers underneath the wings, both inboard and outboard, for comparison, and forgot to put one back on. In theory they were only touching the left wing, nothing else.
Taught me to do a thorough check of the whole plane, inside and out, no matter what the maintenance company has done - they could have touched anything while doing the work.

[Apologies for the thread drift.]

Re: DA40 Fuel Pump Operation

by pietromarx » Fri Mar 16, 2018 5:09 am

Having just replaced a Hartzell composite prop due to an undisclosed lightning strike that happened before purchase, I can tell you that I have closely examined what Hartzell, my A&P, and everyone else says about a prop. Unexpectedly spending $20k on something focuses the mind.

Hartzell and my A&P are extremely clear: at least 3 times is the thing to do. I've seen props which are sluggish until the 3rd, even 5th time through. The goal isn't the number inasmuch as making sure that the prop changes pitch smoothly.

Deaken is somewhat ambiguous as his pieces says, "How many times should you cycle the prop? If the RPM drops smoothly and properly, once is enough. The fresh oil will probably cause the piston to move a good deal and when it comes back to the low pitch stops, most of the "old" oil will be pushed out. If you really want to feel good, do it twice, to get even more of that "old" oil out of there. Three times is gross overkill, in my opinion, but a lot of people do three times, or more. In reality, there are tiny bleed holes that allow a constant flow of warm oil to both sides of the prop piston, so even if you take off with cold oil in there, it will quickly be replaced with nice slippery warm stuff. On some of the big old props on the radials, in extreme Arctic conditions, the oil would congeal faster than the bleed ports could replace it, but I doubt you'll find any modern props with this problem. I should note for completeness that many of the props on the big radials might require many more cycles to achieve a smooth RPM drop when cold. In freezing temperatures, it may take up to ten cycles. There's a lot more to the mechanism, and a lot more oil involved."

Re: DA40 Fuel Pump Operation

by smoss » Fri Mar 16, 2018 2:44 am

Colin- thread drift, but why is the prop cycling potentially harmful? The one time I forgot to do it in the past, when went to full throttle for takeoff, there was a noticeable hesitation in the prop, at which time I immediately recalled I had forgotten that step... perhaps it was totally unrelated, but seemed directly related.

Re: DA40 Fuel Pump Operation

by Colin » Fri Mar 16, 2018 2:14 am

John Deakin taught me that some of the things the manufacturer wants you to do are bad for your plane. His example was that pulling the prop control three times was pointless and potentially harmful, so he only did that after maintenance or after the engine had sat for more than a week. I read a whole column on his reasoning and I believe him. In my DA40 there were a couple things like that which I skipped.

I put a red ring on the circuit breaker for the autopilot. I have tried manually overpowering it and I can do it, but I wouldn't try. If the red button on my stick didn't work that red collar is getting pulled very very quickly.

Free and correct? EVERY TIME. I'm not sure HOW the ailerons could get cross wired while my plane has sat quietly at lunch, but I still check it. And when I lean the stick over and check I hear my friend Susan say, "Up yours," which was her verbal check that the correct one popped up.

Most things on that checklist, every single time I start the engines. I totally understand the checklist keep us from having more accidents. Follow checklist: it all gets done. Don't follow checklist: you run your Gulfstream off the end of the runway with the control lock in place. Seems impossible when you are first learning, then you read all the NTSB reports (which I do), and it is clearly possible.

Re: DA40 Fuel Pump Operation

by gordsh » Thu Mar 15, 2018 10:58 pm

I do but I am a student pilot at this time...I have not yet had a chance to develop some "skip over that" habits ;)

Re: DA40 Fuel Pump Operation

by Rich » Thu Mar 15, 2018 4:48 pm

OK, now that conforming to the check list vis-a-vis the fuel pump running or not is settled, how many folks really adhere to the entire pre-takeoff checklist? I specifically refer to the AP items as an example. ;)

Top