Alternator Problem
Moderators: Rick, Lance Murray
- nrenno
- 3 Diamonds Member
- Posts: 54
- Joined: Sat Jun 18, 2011 1:35 am
- First Name: Nilton
- Aircraft Type: DA40
- Aircraft Registration: N63WP
- Airports: KARB
- Has thanked: 18 times
- Been thanked: 3 times
Alternator Problem
I got a high load electrical warning shortly after taking off. The voltage remained in the middle of the green zone. Turning the master and alternator switch off and back on did not resolve the problem. However, while returning to the airport the warning disappeared.
My mechanic was able to repeat the problem on the ground, but was not able to find any problem with the alternator. He stated that the high load warning continued even after turning the engine off, indicated that the warning might be due to a sensor or G1000 issue.
Has anyone experienced a similar problem? If so, what was the cause?
My plane is a 2005 DA40.
Thanks
My mechanic was able to repeat the problem on the ground, but was not able to find any problem with the alternator. He stated that the high load warning continued even after turning the engine off, indicated that the warning might be due to a sensor or G1000 issue.
Has anyone experienced a similar problem? If so, what was the cause?
My plane is a 2005 DA40.
Thanks
- nrenno
- 3 Diamonds Member
- Posts: 54
- Joined: Sat Jun 18, 2011 1:35 am
- First Name: Nilton
- Aircraft Type: DA40
- Aircraft Registration: N63WP
- Airports: KARB
- Has thanked: 18 times
- Been thanked: 3 times
Re: Alternator Problem
My mechanic discusssed the alternator problem with Diamond, but did not find a solution to the problem yet. The alternator load indicator has been getting stuck in the maximum (40 Amps), while the voltage stays in the middle of the green band.
Does anyone have any insights on possible causes of this problem?
Thanks.
Does anyone have any insights on possible causes of this problem?
Thanks.
- Chris B
- 5 Diamonds Member
- Posts: 843
- Joined: Wed Sep 26, 2012 1:52 am
- First Name: Chris
- Aircraft Type: DA40
- Aircraft Registration: N171CB
- Airports: KRHV
- Has thanked: 210 times
- Been thanked: 215 times
Re: Alternator Problem
Particularly since the problem remained with the engine off, you probably have either a significant short-circuit or defective load sensor, or intermittent connection to the load sensor. The latter two seem more likely, since a 40A short would generate a lot of heat (/flame).nrenno wrote:Does anyone have any insights on possible causes of this problem?
One relatively simple check would be via an inductive current probe. Since the problem can (sometimes) be replicated on the ground it should be straightforward to determine if 40A is *actually* coursing through the circuits. I'd start with tapping the alternator output connection, since that is easy to access.
Chris
- nrenno
- 3 Diamonds Member
- Posts: 54
- Joined: Sat Jun 18, 2011 1:35 am
- First Name: Nilton
- Aircraft Type: DA40
- Aircraft Registration: N63WP
- Airports: KARB
- Has thanked: 18 times
- Been thanked: 3 times
Re: Alternator Problem
Hi Chris,
Thank you very much for the suggestions. I will pass them to my mechanic.
Regards,
—Nilton
Thank you very much for the suggestions. I will pass them to my mechanic.
Regards,
—Nilton
- nrenno
- 3 Diamonds Member
- Posts: 54
- Joined: Sat Jun 18, 2011 1:35 am
- First Name: Nilton
- Aircraft Type: DA40
- Aircraft Registration: N63WP
- Airports: KARB
- Has thanked: 18 times
- Been thanked: 3 times
Re: Alternator Problem
Chris,
Thank you for the help. My mechanic at Solo Aviation found the problem. The current sensor (see picture), located behind the panel had failed. It was very difficult to find the sensor because it is hidden behind the circuit breakers.
Regards,
--Nilton
Thank you for the help. My mechanic at Solo Aviation found the problem. The current sensor (see picture), located behind the panel had failed. It was very difficult to find the sensor because it is hidden behind the circuit breakers.
Regards,
--Nilton
- gordsh
- 3 Diamonds Member
- Posts: 194
- Joined: Wed Jun 21, 2017 4:40 pm
- First Name: Shawn
- Aircraft Type: DA40
- Aircraft Registration: CCCCC
- Airports:
- Has thanked: 90 times
- Been thanked: 41 times
Re: Alternator Problem
Good find, I think you should buy your mechanic a case of beer or wine. Thanks for the picture
- Lance Murray
- 5 Diamonds Member
- Posts: 1163
- Joined: Tue Jul 06, 2010 11:25 pm
- First Name: Lance
- Aircraft Type: DA40
- Airports:
- Has thanked: 7 times
- Been thanked: 120 times
Re: Alternator Problem
Interesting that it looks like they used a Hall effect device and not a shunt.
- Steve
- 5 Diamonds Member
- Posts: 1973
- Joined: Thu Aug 12, 2010 1:23 am
- First Name: Steve
- Aircraft Type: DA40
- Aircraft Registration: N432SC
- Airports: 1T7
- Has thanked: 85 times
- Been thanked: 504 times
Re: Alternator Problem
Even the old VM-1000 uses a Hall effect device, one equally difficult to find behind the instrument panel...
Steve
Steve
- nrenno
- 3 Diamonds Member
- Posts: 54
- Joined: Sat Jun 18, 2011 1:35 am
- First Name: Nilton
- Aircraft Type: DA40
- Aircraft Registration: N63WP
- Airports: KARB
- Has thanked: 18 times
- Been thanked: 3 times
Re: Alternator Problem
The high load electrical warning (>80 Amps) returned after he Hall effect sensor was changed, but is intermittent. The warning appears when the G1000 is turned on and disappears after a few minutes. I asked my mechanic to replace the voltage regulator to see it solves the problem.
Does anyone have other suggestions?
Does anyone have other suggestions?
- nrenno
- 3 Diamonds Member
- Posts: 54
- Joined: Sat Jun 18, 2011 1:35 am
- First Name: Nilton
- Aircraft Type: DA40
- Aircraft Registration: N63WP
- Airports: KARB
- Has thanked: 18 times
- Been thanked: 3 times
Re: Alternator Problem
Finally, the problem was resolved. Besides the Hall effect sensor, a diode had to be replaced. My mechanic suspects that the diode "burned out" when the sensor failed.